Fluoro-Photoacoustic Polymeric Renal Reporter for Real-Time Dual Imaging of Acute Kidney Injury

Photoacoustic (PA) imaging agents detect disease tissues and biomarkers with increased penetration depth and enhanced spatial resolution relative to traditional optical imaging, and thus hold great promise for clinical applications. However, existing PA imaging agents often encounter the issues of slow body excretion and low-signal specificity, which compromise their capability for in vivo detection. Herein, a fluoro-photoacoustic polymeric renal reporter (FPRR) is synthesized for real-time imaging of drug-induced acute kidney injury (AKI). FPRR simultaneously turns on both near-infrared fluorescence (NIRF) and PA signals in response to an AKI biomarker (γ-glutamyl transferase) with high sensitivity and specificity. In association with its high renal clearance efficiency (78% at 24 h post-injection), FPRR can detect cisplatin-induced AKI at 24 h post-drug treatment through both real-time imaging and optical urinalysis, which is 48 h earlier than serum biomarker elevation and histological changes. More importantly, the deep-tissue penetration capability of PA imaging results in a signal-to-background ratio that is 2.3-fold higher than NIRF imaging. Thus, the study not only demonstrates the first activatable PA probe for real-time sensitive imaging of kidney function at molecular level, but also highlights the polymeric probe structure with high renal clearance.     

A Flexi-PEGDA Upconversion Implant for Wireless Brain Photodynamic Therapy

Near-infrared (NIR) activatable upconversion nanoparticles (UCNPs) enable wireless-based phototherapies by converting deep-tissue-penetrating NIR to visible light. UCNPs are therefore ideal as wireless transducers for photodynamic therapy (PDT) of deep-sited tumors. However, the retention of unsequestered UCNPs in tissue with minimal options for removal limits their clinical translation. To address this shortcoming, biocompatible UCNPs implants are developed to deliver upconversion photonic properties in a flexible, optical guide design. To enhance its translatability, the UCNPs implant is constructed with an FDA-approved poly(ethylene glycol) diacrylate (PEGDA) core clad with fluorinated ethylene propylene (FEP). The emission spectrum of the UCNPs implant can be tuned to overlap with the absorption spectra of the clinically relevant photosensitizer, 5-aminolevulinic acid (5-ALA). The UCNPs implant can wirelessly transmit upconverted visible light till 8 cm in length and in a bendable manner even when implanted underneath the skin or scalp. With this system, it is demonstrated that NIR-based chronic PDT is achievable in an untethered and noninvasive manner in a mouse xenograft glioblastoma multiforme (GBM) model. It is postulated that such encapsulated UCNPs implants represent a translational shift for wireless deep-tissue phototherapy by enabling sequestration of UCNPs without compromising wireless deep-tissue light delivery.     

Photonic Metamaterial Absorbers: Morphology Engineering and Interdisciplinary Applications

Recent advances in nanofabrication technologies have spurred many breakthroughs in the field of photonic metamaterials that provide efficient ways of manipulating light–matter interaction at subwavelength scales. As one of the most important applications, photonic metamaterials can be used to implement novel optical absorbers. First the morphology engineering of various photonic metamaterial absorbers is discussed, which is highly associated with impendence matching conditions and resonance modes of the absorbers, thus directly determines their absorption efficiency, operational bandwidth, incident angle, and polarization dependence. Then, the recent achievements of various interdisciplinary applications based on photonic metamaterial absorbers, including structural color generation, ultrasensitive optical sensing, solar steam generation, and highly responsive photodetection, are reviewed. This report is expected to provide an overview and vision for the future development of photonic metamaterial absorbers and their applications in novel nanophotonic systems.     

光学材料的磨削损伤控制试验研究

基于K9玻璃不同的磨削工艺参数确定其磨削损伤层深度随工艺参数变化的规律，并通过工件磨削损伤层深度的动态检测研究其裂纹扩展规律。结果表明:工件磨削过程中的裂纹损伤是动态扩展过程。固定工艺参数下，裂纹稳态扩展，损伤层深度不变；采用损伤更小的工艺参数磨削，裂纹的扩展速度小于材料的去除速度，其损伤层深度逐渐减小，损伤的去除速度逐渐减慢直至二者间达到稳态平衡。同时，为了去除前道工序的损伤层，后道工序的材料去除量需达到前道工序损伤层深度的2～3倍。      

Damage evolution in SiC/SiC unidirectional composites by X-ray tomography

Melt infiltrated SiC/SiC ceramic matrix composite unidirectional (UD) composite specimens were imaged under load using X-ray microtomography techniques in order to visualize the evolution of damage accumulation and to quantify damage mechanisms within the composite such as matrix cracking and fiber breaking. The data obtained from these in situ tensile tests were used in comparison with current models and literature results. Three-dimensional (3D) tomography images were used to measure the location and spacing of matrix cracking that occurred at increasing stress increments during testing within two UD composite specimens. The number of broken fibers and the location of each fiber break gap that occurred within the volume of both specimens were also quantified. The 3D locations of fiber breaks were correlated with the location of each matrix crack within the volume of the specimen and it was found that at the stress scanned directly before failure, most of the fiber breaks occur within 100 microns of a matrix crack.     

Investigation of fluidized bed behaviour using electrical capacitance tomography

The temporal and cross-sectional distributions of particles in a 127 mm diameter fluidized bed have been obtained using a new generation, high-speed electrical capacitance tomography. Two planes of eight electrodes were used and mounted at 160 and 660 mm from the gas distributor which was a 3 mm thick porous plastic plate (maximum pore size of 50-70 μ m). 3 mm diameter, nearly-spherical polyethylene granules made up the bed. Experiments at sampling frequencies of 200-2000 cross-sections per second and gas superficial velocities from just below the minimum fluidization to 83% above minimum fluidization velocities were used. The time series of the cross-sectional average void fractions have been examined both directly and in amplitude and frequency space. The last two used probability density functions and power spectral densities. The information gathered shows that the fluidized bed was operating in the slugging mode, which is not surprising given the size of the particles. It has been found that an increase in the excess gas velocity above the minimum fluidization velocity resulted in an increase in the mean void fraction, an increase in the length and velocity of the slug bubbles as well as the bed height, and a slight decrease in the slug frequency. The results are presented in a level of detail suitable for comparison with later numerical simulation.     

Applicability of electrical resistance tomography to the analysis of fluid distribution in haemodialysis modules

This work aims to explore the applicability of electrical resistance tomography (ERT) in the analysis of fluid distribution in haemodialysis modules, which is not straightforward due to the complex geometry of the hollow fibre bundles and the small sizes of the modules. On the other hand, ERT is potentially a suitable and convenient technique for investigation in this field due to its cost-effectiveness and capacity to perform measurements in opaque systems. After a preliminary estimation of the fibre bundle local distribution, the assessment of the technique is performed by observing the time evolution of the measured conductivity maps during the module filling and emptying operations with water and air, which are alternatively fed inside or outside the fibre bundle. Reliable conductivity maps are obtained by placing the module vertically or horizontally. Additional experimental data collected by feeding liquid mixtures of different sodium chloride concentrations show that the technique is suitable for detecting concentration variations, due to the mass transfer through the fibres, and flow maldistribution, due to the specific geometry of the module. From the preliminary results collected in this work, the technique appears to be adequate for the collection of data that can support the optimization of the module geometry and computational model validation.     

Synthesis of highly transparent and thermally stable copolyimide with fluorine-containing dianhydride and alicyclic dianhydride

The development of optical films is highly desirable for applications in flexible displayers. In this work, a copolyimide (co-PI) film with high thermal stability and high transparency was prepared by the copolymerization of 2,2′-bis(trifluoromethyl)-4,4′-diaminodiphenyl ether, cyclobutanetetracarboxylic dianhydride, and 4,4′-(hexafluoroisopropylidene)diphthalic anhydride (6FDA). The effects of aliphatic dianhydride and fluorine dianhydride monomers on the optical, thermal, and mechanical properties of the co-PIs were discussed in detail based on the experimental results and theoretical simulations. We found that the preparation of polyimide (PI) based on the combination of two dianhydrides could obtain the PI film with excellent comprehensive performance due to nonconjugated structure and strong electron-withdrawing effect. Through the structure and composition optimization, a PI film of PI-6FDA-70 with T_g of 300 °C, T_d10% more than 500 °C, the average transparency of 90% and the elongation at the breakage more than 8% was prepared. Such molecular design provides a practical approach to develop high-performance colorless PI films. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48603.